HPC-P27 PCS1900mhz Mobile Phone signal booster

Cell phone signal booster (also named repeater, amplifier) is a product designed to solve the mobile phone blind signal. As the mobile phone signal 

is transmitted by electromagnetic waves to establish a communications link, however there are a lot barriers make it is unavailable to get sound

signal. When people enter some tall buildings, some places basement malls, restaurants and parking lot, some places of entertainment such 

as karaoke sauna and massage, some public place such as subway, tunnel and etc. where cell phone signals can not reach, now the cell phone 

signal booster can solve these problems! The entire range of mobile phone signals can be well used; we all will get great convenience and benefit 

from sound signal.

Our boosters are the perfect solutions for a wireless improvement in the mobile reception!

We provides signal boosters kits for any Homes, Offices, Cars, RV's, Boats and more. All amplifier kits come with Indoor and Outdoor Antennas, Cables, Power adapters and more.

Steps that describe the work of Repeater.

1) The outside antenna receives the signal from the nearest mobile base station.

2) The outside antenna sends the received signal through the coax cable to

the installed Repeater.

3) The Repeater accepts the low signal and improves it.

4) The improved signal goes to the inside antenna through the connection coax cable.

5) The inside antenna send the improved good signal to your mobile phone.

HPC-P-27 PCS1900mhz repeater Features:

1. With unique appearance design, have good cooling function

2. With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;

3. With DL signal LED display, help to install the outdoor antenna at the best state;

4.With AGC and ALC, make repeater work stable . 

5.PCB with isolation function ,make UL and DL signal not influence each other,

6.Low  intermodulation, high Gain ,stable Output power 

HPC-P-27 PCS1900 repeater Inside and Outside Design

HPC-D-27  Dual band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better phone call quality and smoother data transmission. It is designed to support coverage area max can up to 2000 square meters with proper engineering. Below are the main features.

1.The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.

2.Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance.

3.To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals.

4.Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators. 

5.Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance.

6.Multiple phones and other handheld devices throughout a building can benefit from a wireless repeater.

7.Supports up to (500) users / calls simultaneously.

8.Extended phone battery life. (Your phone does not need to put out as much power due to improved reception.)

Specification of HPC-D-27 Dual band repeater:

Electrical specification			Uplink	Downlink
Frequency Range	DCS 1800		1710 ~ 1785 MHz	1805 ~ 1880 MHz
Max .Gain			≥ 75dB	≥ 80dB
Max .Output Power			≥ 24dBm	≥ 27dBm
MGC ( Step Attenuation )			≥ 31dB / 1dB step
Automatic Level Control			≥ 20dB
Gain Flatness		GSM & CDMA	Tpy≤  6dB(P-P); DCS,PCS ≤  8dB(P-P)
		WCDMA	≤  2dB/ 3.84MHz,Full Band ≤  5dB(P-P)
Noise Figure			≤  5dB
VSWR			≤  2.0
Group Delay			≤  1.5μs
Frequency stability			≤  0.01ppm
Spurious Emission & Output inter-modulation			GSM Meet  ETSI TS 151 026 V 6.1.0
			WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )
			CDMA Meet  IS95 & CDMA2000
WCDMA System		Spurious Emission Mask	Meet 3GPP TS 25.143 ( V 6.2.0 )
		Modulation Accuracy	≤  12.5%
		Peak Code Domain Error	≤  -35dB@Spreading Factor 256
CDMA System		Rho	ρ > 0.980
		ACPR	Meet IS95 & CDMA2000
Mechanical  Specifications			Standard
I /O Port			N-Female
Impedance			50 ohm
Operating Temperature			-25ºC~+55ºC
Environment Conditions			IP40
Dimensions			155x112x85mm
Weight			≤  1.50Kg
Power Supply			Input AC90-264V,output DC 5V / 3A
LED  Alarm			Standard
Power LED			Power Indicator
UL LED			Be lighted when there is phone calling
DL 1			Be lighted when Outdoor signal is -65dB
DL 2			Be lighted when Outdoor signal only -55dB
DL 3			Be lighted when Outdoor signal only -50dB

The installtion of the Repeater

Outdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal), 

(Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add more antenna,the HPC-D-27 Max can work with 10pcs indoor antenna.  ( when add antenna ,please remember to take splitters )

Installation steps 

Step 1 Start by taking your phone up to the roof or other location outside to find where the signal is strongest.

Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later.

Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the Signal Repeater.

Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna.

Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here.

Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port.

Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible.

Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation.

Of course there are still a few more things to consider but in general, this is the basic procedure. For more information, please contact us.

Terms and Conditions

Certificate	CE/RoHs
Country of Origin	China
Port of Dispatch	Shenzhen
Production Capacity	1000pcs/month
Date of Delivery	Within 3 days after received payment inform
MOQ	10pcs
Warranty	2years
Pacakge	1pcs/box; 20pcs/carton
Country of Origin	China